RE: NEC-LIST:comments and sub-sections

Sorry I misled you. I spoke too quickly. I've never actually tried this at
the beginning of a line. I just tried it and it doesn't work. The
NEC-WIN-PRO manual says that you can use an exclamation point to ADD
comments to a line as follows:

GW 1 5 0 0 0 0 5 .001 !example of a comment

I've done this on NEC-WIN-PRO, but never knew about it when I had
stand-alone NEC2. I hope it works for you. Even so, the only way you're
going to be able to comment out whole sections of an input file is to
backspace them on to the previous line and put the ! in front of the
unwanted section as above.

Sorry for the inconvenience.

Regards,

John

                -----Original Message-----
                From: Brent DeWitt [mailto:bdewitt_at_ix.netcom.com]
                Sent: Tuesday, June 18, 2002 8:38 PM
                To: Yorko, John
                Subject: RE: NEC-LIST:comments and sub-sections

                Thanks John!

                -----Original Message-----
                From: Yorko, John [mailto:John.Yorko_at_itt.com]
                Sent: Tuesday, June 18, 2002 9:08 AM
                To: 'Steve Inge'; bdewitt_at_ix.netcom.com
                Cc: NEC List
                Subject: RE: NEC-LIST:comments and sub-sections

                Use an exclamation point at the beginning of the line you
want to comment
                out.

                John Yorko

                                -----Original Message-----
                                From: Steve Inge
[mailto:sringe_at_actrix.gen.nz]
                                Sent: Monday, June 17, 2002 3:08 AM
                                To: bdewitt_at_ix.netcom.com
                                Cc: NEC List
                                Subject: Re: NEC-LIST:comments and
sub-sections

                                The only method that I know works, is to
move the unwanted
                cards to
                                after the EN card. Depending on what you
want to achieve,
                you could
                                put a GE, followed by an EN card.

                                Brent DeWitt wrote:
>
> Is there a way to "comment out" sections
of a NEC2
                geometery input file?
> I've tried moving the GE card up, but I
get an error on
                the first GW card
> after it and that aborts the run. It also
seems that
                CM/CE cards aren't
> allowed after the first geometry card.
>
> Any help would be appreciated!
>
> Brent DeWitt
> --
> The NEC-List mailing list
<nec-list_at_gweep.ca>
>
http://www.gweep.ca/mailman/listinfo.cgi/nec-list

                                --
                                sringe_at_actrix.gen.nz,
        
Steve.Inge_at_ieee.org-------------------------------
                                Steve Inge, ZL2BDV, RF Engineering Analyst.
Island Bay,
                Wellington, New
                                Zealand.
                                Phone +64 4 3838 422, Fax: +64 4 3838 691.
Mobile +64 25
                463 330.
                                --
                                The NEC-List mailing list
<nec-list_at_gweep.ca>
        
http://www.gweep.ca/mailman/listinfo.cgi/nec-list

                ************************************
                If this email is not intended for you, or you are not
responsible for the
                delivery of this message to the addressee, please note that
this message may
                contain ITT Privileged/Proprietary Information. In such a
case, you may not
                copy or deliver this message to anyone. You should destroy
this message and
                kindly notify the sender by reply email. Information
contained in this
                message that does not relate to the business of ITT is
neither endorsed by
                nor attributable to ITT.
                ************************************

************************************
If this email is not intended for you, or you are not responsible for the
delivery of this message to the addressee, please note that this message may
contain ITT Privileged/Proprietary Information. In such a case, you may not
copy or deliver this message to anyone. You should destroy this message and
kindly notify the sender by reply email. Information contained in this
message that does not relate to the business of ITT is neither endorsed by
nor attributable to ITT.
************************************

-- 
The NEC-List mailing list <nec-list_at_gweep.ca>
http://www.gweep.ca/mailman/listinfo.cgi/nec-list